End Fed

End Fed multiband antenna DIY kit for 10-15-20-40-80m 300Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.50 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 110uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: approx. 600g Balun 1:49Informationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.netAdresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed multiband antenna DIY kit for 10-15-20-40-80m 100Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-15-20-40-80 meters up to 100 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!: This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-140-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.00 meter1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 110uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 23 meters Connection: PL Max. Power: 100Watt PEP Phone Weight: approx. 500g Balun 1:49 Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed multiband antenna DIY kit for 10-20-40m 300Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-20-40meters up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.50 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 12 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: approx. 600g Balun 1:49 Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed multiband antenna DIY kit for 10-20-40m 100Watt PEP SSBNew extended kit! This kit contains all the necessary components to build an EndFed 1:49 multiband antenna for the bands 10-20-40meters up to 100 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited.  LF Antenna Strand - New! This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-140-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.0 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: MultibandLength: approx. 12 meters Connection: PL Max. Power: 100Watt PEP Phone Weight: approx. 550g Balun 1:49 Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

New extended kit! This kit contains all the necessary components to build an EndFed 1:649 multiband antenna for the bands 10-12-15-17-20-(30*)-40-80-160 up to 300 Watt PEP Phone. We have added a connection for the counterweight and the useful stainless steel ring etc. to the kit. This End Fed kit is supplied with the antenna wire of your choice: Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. LF Antenna Strand - New!This high-quality antenna strand consists of 32 individual 0.20 mm wires made of hard-drawn, bare copper. The conductor cross-section is approximately 1.0 mm² and offers excellent conductivity combined with high mechanical strength. It has a total diameter of 2.1 mm, a weight of approx. 11 g/m, and a breaking load of about 40 kg. The robust black polyethylene (PE) insulation reliably protects the strand from environmental influences and ensures a long service life. The kit contains the following components: 1x toroidal core FT-240-431x enameled copper wire GR2 for winding the toroidal core (1mm) approx. 1.80 meters1x polycarbonate housing with transparent cover 100x100x60 mm (IP67)1x mini insulator 65 * 15mm2x simplex terminals up to 2 mm wire (wire rope terminal) 1x thimble approx. 23.5 meter antenna wire 1mm² black 1x capacitor 100pF 2kV DC 1x PL259 panel jack 1x extension coil 34uH ready wound and measured 1x shrink tube black 25.4-12.7mm 1x various screws, washers and nuts made of stainless steel 1x stainless steel ring 3x Fast-On ring contactType: Multiband 1:64 Length: approx. 46 meters Connection: PL Max. Power: 300/600Watts PEP Phone Weight: ca 600g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

Mini Endfed antenna kit, max 100 watts for 10-15-20-40 meters approx. 20 meters long, without extension coil.The Mini Endfed is a small End Fed antenna solution for portable use, when travelling, POTA, QRP, SOTA (Summit on the Air) or DX expeditions etc. The IP65 protected housing made of polycarbonate with a size of only 64x58x35 mm can be easily stowed in a pocket or backpack, but is also robust enough for stationary mounting. The weight is around 400-500 grams, depending on the length of the antenna. If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you can be on air within a few minutes! To attach the housing of the 1:49 transformer to a mast, the same bracket can be used as for our active antennas. This Mini Endfed kit is supplied with an antenna wire of your choice:Standard antenna wire: This antenna wire consists of 1.0 mm2 fine stranded copper conductor with black PVC insulation. The total diameter is approx. 2 mm. Ideal for experiments or vacation antennas. As the core is only made of copper, this stranded wire will become slightly longer and therefore thinner over time. The tensile strength of this stranded antenna wire is limited. Copper/Kevlar stranded antenna wire This stranded antenna wire is specially manufactured for antennas. The stranded wire consists of a Kevlar core with approx. 1.1 mm2 tinned and fine-stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The sheathing is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You receive a strong, flexible and relatively light antenna strand. These complete Mini End Fed Multiband kits are designed for 100 Watt PEP Phone and are available in these versions: 10-15-20-40 meters approx. 20 meters long, without extension coil 10-20-40 meters, approx. 12 meters long, with 34uH extension coil 10-15-20-40-80 meters, approx. 21 meters long with 110uH extension coilThe kit contains the following components: approx. 20.45 meters of antenna wire 1x stainless steel cable clamp 1x end insulator 1x cable lug 5mm 1:49 Mini Impedance transformer: IP65 housing 64x58x35mm polycarbonate Toroidal core FT140-43 Enameled copper wire GR2 quality 1.00 mm 100 pF capacitor 2kV 1x BNC flange socket 2x M2.5 screws 8/10mm 2x M2.5 nut 2x M2,5 washer 1x cable lug 3mm 3x M5 cable lug 2x stainless steel M5 screw 20mm 2x stainless steel M5 wing nut 2x stainless steel M5 collar nut 2x stainless steel M5 toothed washer 2x stainless steel M5 screw 20mm 2x stainless steel M5 wing nut 2x stainless steel M5 collar nut 2x stainless steel M5 toothed washer 1x ring M4 1x toothed washer M4 1x nut M4 1x cable thimbleYou can find the assembly instructions here: LINK Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

Mini Endfed Antennenbausatz, für 10-20-40m mit Verlängerungsspule, max 100Watt PEP Die Mini Endfed ist eine kleine End Fed Antennen Lösung für den Portabeleinsatz,, auf Reisen, QRP, SOTA (Summit on the Air) oder DX Expeditionen usw. Das IP65 geschütze Gehäuse aus Polcarbonat, hat eine Größe von nur 64x58x35 mm und lässt sich leicht in der Tasche oder im Rucksack verstauen, ist aber auch robust genug für die stationäre Montage. Das Gewicht beträgt etwa 400-500 Gramm. Der Bausatz hat sowohl einen Anschluss für die ANTenne als auch GND für ein Gegengewicht. Den M4 Ring haben wir ebnso integriert. Damit lässt sich die Mini Endfed ganz einfach mit einem Karabiner befestigen und mit der Kausche als Zugentlasung vewenden. Alle Schrauben, Muttern und der Ring sind aus Edelstahl. Befestigt man die Antenne an der Spitze eines Teleskopmast, schiebt die Mastsegmente heraus, ist man innerhalb von wenigen Minuten auf Sendung! Um das Gehäuse des 1:49 Transformers an einem Mast zu befestigen, kann die gleiche Halterung wie von unseren Aktivantennen verwendet werden.  Dieser Mini Endfed-Bausatz wird mit einem Antennendraht Ihrer Wahl geliefert: Standard Antennenlitze:Diese Antennenlitze besteht aus 1,0 mm2 feindrähtiger Kupferleiter mit einer schwarzen PVC Isolierung. Der Gesamtdurchmesser beträgt etwa 2 mm. Ideal für Experimente oder Urlaubsantennen. Da der Kern nur aus Kupfer besteht, wird sich diese Litze mit der Zeit immer etwas längen und somit dünner werden. Die Zugfestigkeit dieser Antennenlitze ist begrenzt. LF-Antennenlitze - Neu! Diese hochwertige Antennenlitze besteht aus 32 Einzeldrähten à 0,20 mm aus hartgezogenem, blankem Kupfer. Der Leiterquerschnitt beträgt ca. 1,0 mm² und bietet hervorragende Leitfähigkeit bei gleichzeitig hoher mechanischer Festigkeit. Sie hat einen Gesamtdurchmesser von 2,1 mm, einem Gewicht von ca. 11 g/m und einer Bruchlast von etwa 40 kg. Die robuste Polyethylen-Isolation (PE) in schwarz schützt die Litze zuverlässig vor Umwelteinflüssen und sorgt für eine lange Lebensdauer In diesem Bausatz sind alle nötigen Bauteile zum Bau einer Mini EndFed Multiband Antenne für die Bänder 10-20-40 Meter bis100 Watt PEP Phone enthalten. Der Bausatz enthält die folgenden Bauteile:  ca. 12 Meter AntennendrahtVerlängerungsspule mit ca: 34uh (fertig gewickelt und vermessen)1x Edelstahl Kabelklemme1x Endisolator1x Kabelschuh 5mm1x Schrumpfschlauch 1:49 Mini Impedanztransformator: IP65-Gehäuse 64x58x35mm PolycarbonatRingkern FT140-43Kupferlackdraht GR2 Qualität 1,00 mm100 pF Kondensator 2kV1x BNC-Flanschbuchse2x M2,5 Schrauben 8/10mm2x M2,5 Mutter2x M2,5 Unterlegscheibe1x Kabelschuh 3mm3x M5 Kabelschuh2x Edelstahl M5 Schraube 20mm2x Edelstahl M5 Flügelmutter2x Edelstahl M5 Kragenmutter2x Edelstahl M5 Zahnscheibe2x Edelstahl M5 Schraube 20mm2x Edelstahl M5 Flügelmutter2x Edelstahl M5 Kragenmutter2x Edelstahl M5 Zahnscheibe1x Ring M41x Zahnscheibe M41x Mutter M41x Kabelkausche Die Bauanleitung finden Sie hier: ZUR BAUANLEITUNG    ** Die Bauanleitung bekommt gerade noch ihren Feinschliff

Mini Endfed Antenna Kit for 10-15-20-40-80m, max 100 Watts PEP and 1:49 Transformer The Mini Endfed is a small endfed antenna solution for mobile use, travel, QRP, SOTA (Summit on the Air) or DX expeditions etc. The IP65 protected polar carbonate housing with a size of only 64x58x35 mm, can be easily stored in your pocket or backpack. The weight is about 250-500 grams, depending on the length of the spotlight. The kit has both a connector for the ANTenna and GND for a counter poise capacitance. We have also integrated the M4 ring. This makes it very easy to attach the Mini Endfed with a carabiner and use the thimble as a strain relief. All screws, nuts and the ring are made of stainless steel. If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you are on the air within minutes! To attach the body of the 1:49 Transformer to a mast, you can use the same bracket as used by our active antennas. This End Fed Multiband Antenna comes with the antenna wire of your choice: Standard Antenna wire: This antenna litz wire is made of 1.0 mm2 fine stranded copper conductor with a black PVC insulation. The total diameter is about 2 mm. Ideal for experiments or vacation antennas. Since the core is only copper, this stranded wire will always elongate a bit over time, making it thinner. The tensile strength of this antenna strand is limited. Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. These complete Mini End Fed Multiband kits are designed for 100 Watt PEP Phone and are available in these configurations: 10-20-40 meters approximately 20 meters in length, without extension coil.10-20-40 meters, approx. 12 meters length, with 34uH extension coil10-15-20-40-80 meters, approximately 21 meters in length with 110uH extension coil. This kit contains: 23 meters of antenna wire19 mm PVC pipe with approx: 110uh coil1x stainless steel cable clamp1x end insulator1x cable lug 5mm1x heat shrink tubing 1:49 Mini impedance transformer:IP65 housing 64x58x35mm polycarbonateFerrite toroid Amidon FT140-43Winding wire 1,00 mm100 pF capacitor 1kV1x BNC flange socket2x M2,5 screws 8/10mm2x M2,5 nut2x M2,5 washer1x cable lug 3mm3x M5 cable lug2x stainless steel M5 screw 20mm2x stainless steel M5 wing nut2x stainless steel M5 collar nut2x stainless steel M5 lock washer2x stainless steel M5 screw 20mm2x stainless steel M5 wing nut2x stainless steel M5 collar nut2x stainless steel M5 tooth lock washer1x ring M41x tooth lock washer M41x nut M41x cable thimble You can find the building instructions here: TO THE CONSTRUCTION INSTRUCTION ** The construction manual is just getting its fine tuning

Extension coil for 10-15-20-40m End Fed Single extension coil 34uH for the 10-15-20-40m Bands. As a spare part, extension or for experimenting. Completely wrapped with 0.6mm² enamelled copper wire. 20mm PVC pipe approx. 12cm long Approximately 34uH Approx. 12cm shrink tube.  

Extension coil for 10-15-20-40-80m EndFed Single extension coil 110uH for the 10-15-20-40-80m Bands. As a spare part, extension or for experimenting. Completely wrapped with 0.6mm² enamelled copper wire. 20mm PVC pipe approx. 21cm long Approximately 110uH Approx. 20cm shrink tube.  

Extension coil for 160m Band EFHW/End Fed Single extension coil 192uH for the 160m Band. As a spare part, extension or for experimenting. Completely wrapped with 0.6mm² enamelled copper wire. 20mm PE pipe approx. 28cm long Approximately 192uH Approx. 28cm shrink tube.  

Fabricated 110uH extension coil for 80m "ready to go" Single extension coil for the 80m band. The coil has approx 110uH and comes ready assembled with screws, cable lugs and shrink wrapped already. Cable lugs and wing nuts are included for attaching the antenna wire. The glands are made of stainless steel.  Completely wrapped with 0.6mm² enamelled copper wire. 20mm PVC pipe approx. 21cm long Approximately 110uH Stainless steel screws TestedReady to on the air  

Fabricated 192uH extension coil for 160m "ready to go" Single extension coil for the 160m band  "ready to go". The coil has approx 192uH and comes ready assembled with screws, cable lugs and shrink wrapped already. Cable lugs and wing nuts are included for attaching the antenna wire. The glands are made of stainless steel.  Pre-wound with 0.6mm² enameled copper wire On 20mm PVC pipe approx. 28cm long, with heat-shrink tubing Approx. 192uH Stainless steel screws TestedReady to go on the air  

Fabricated extension coil 34uH for the 40m Band "ready to go". Single extension coil for the 40m band. The coil has approx34uH and comes ready assembled with screws, cable lugs and shrink wrapped already. Cable lugs and wing nuts are included for attaching the antenna wire. The glands are made of stainless steel.  Completely wrapped with 0.6mm² enamelled copper wire. 20mm PVC pipe approx. 21cm long Approximately 34uH ready to go on the air  

Ferrite toroid FT 240-43 for example End Fed antennas Single FT 240-43 Ferrite toroid for the build of a balun or an end fed antenna or as replacement or extension of the end fed kits offered by us. Type: toroidal coreDimensions: 61 (Dia.) x 12.7mmApplication: End Fed Antenna / BalunMaterial 240-43Diameter 61mmHeight: 12.7mmInner diameter: 35.55mmOuter diameter: 61mmScope of delivery1x Ferrite toroid FT 240-43

Ferrite toroid FT 140-43 Single FT140-43 Ferrite toroid for the construction of a balun or an end fed antenna or as replacement or extension of the end fed kits offered by us. Type: Ferrite toroidDimensions: 35.55 (Dia.) x 12.7mmApplication: End Fed Antenna / BalunMaterial 140-43Diameter 35.55mmHeight: 12.7mmInner diameter: 23mmScope of delivery1x Ferrite toroid FT 140-43

Ferrite toroid FT 82-43 Single FT 82-43 Ferrite toroid for the construction of a balun or an end fed antenna or as replacement or extension of the end fed kits offered by us. Type: Ferrite toroidDimensions: 21mm (Dia.) x 6,35mmApplication: End Fed Antenna / BalunMaterial FT 82-43Diameter 21mmHeight: 6,53mmInner diameter: 13mmScope of delivery1x Ferrite toroid FT 82-42

End Fed Multiband Antenna for 10-15-20-40-80m 300Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: ca  650g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed Multiband Antenna for 10-12-15-17-20-(30*)-40-80-1600m - 300Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-12-15-17-20-(30*)-40-80-160 meters up to 300/600Watts PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband 1:64 Length: approx. 46 meters Connection: PL Max. Power: 300/600 Watts PEP Phone Weight: ca 750g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

Mini End Fed Multiband Antenna You don't have time to build a Mini End Fed Multiband Antenna?No problem. We offer you a ready made Mini End Fed Multiband Antenna for the bands 10-15-20-40m or 10-15-20-40-80m up to 100 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band area. The Mini Endfed is a small end fed antenna solution for mobile use, travel, QRP, SOTA (Summit on the Air) or DX expeditions etc. The IP65 protected polycarbonate case with a size of only 64x58x35 mm, can be easily stored in your pocket or backpack. The weight is about 400-500 grams, depending on the radiator length. This Mini End Fed antenna includes the following parts in addition to the standard parts: thimble, ground connection, deluxe extension coil. This End Fed Multiband Antenna comes with the antenna wire of your choice: Standard Antenna wire: This antenna litz wire is made of 1.0 mm2 fine stranded copper conductor with a black PVC insulation. The total diameter is about 2 mm. Ideal for experiments or vacation antennas. Since the core is only copper, this stranded wire will always elongate a bit over time, making it thinner. The tensile strength of this antenna strand is limited. Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Technical dataType: MultibandLength: approx. 12 (10-40m) or 23 meters (10-80m)Connection: BNCMax. Power: 100Watt PEP PhoneWeight: approx. 250g   Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

End Fed Multiband Antenna for 10*-15-20-40-80m 1000Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10*-15-20-40-80 meters up to 1000 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:3 instead 1 one ferrite core, Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 1000Watt PEP Phone Max Powaer digitaL: <100 Watts Weight: ca 1100g 10m needs a tuner Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings.

End Fed Multiband Antenna for 10-15-20-40-80m 300Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-15-20-40-80 meters up to 300 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 300Watt PEP Phone Weight: ca  650g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings.

End Fed Multiband Antenna for 10*-15-20-40-80m 1000Watts PEP Phone You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10*-15-20-40-80 meters up to 1000 Watt PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:3 instead 1 one ferrite core, Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband Length: approx. 23 meters Connection: PL Max. Power: 1000Watt PEP Phone Max Powaer digitaL: <100 Watts Weight: ca 1100g 10m needs a tuner Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings.

You don't have time to build an Endfed Multiband Antenna? No problem. We offer you a ready assembled End Fed Multiband for the bands 10-12-15-17-20-(30*)-40-80-160 meters up to 1000 Watts PEP Phone. The antenna is tuned to band center. You only have to tune the antenna (as usual) minimally to the desired band section. This End Fed Multiband Antenna includes the following parts in addition to the standard components:Mounting plate, ring, thimble, ground connection, deluxe extension coil and a pressure equalization valve. This End Fed Multiband Antenna comes with: Copper/Kevlar antenna litz wire This antenna litz wire is manufactured specifically for antennas. The litz consists of a Kevlar core with approx. 1.1 mm2 tinned and fine stranded copper conductors. 1x 0.4 mm Kevlar and 24x 0.25 mm copper. The jacket is made of black UV-resistant PE. The total diameter is approx. 2.5 mm. The tensile strength is approx. 50 kg. You will receive a strong, flexible and relatively light antenna litz wire. Type: Multiband 1:64 Length: approx. 46 meters Connection: PL Max. Power: 1000Watts PEP Phone Weight: ca 750g Info The measurements for this antenna were made on two 12m spider beam masts, 10 meters above the ground, in an open field, without any buildings. Informationen gemäß Art. 19 GPSR Adresse des Herstellers:  Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

1:9 UNUN transformer for the frequency range: 1-30MHz and a maximum transmission power of either 600W or 1500W PEP. The IP67 housing is of course made of UV-resistant polycarbonate. Including connection for a counterweight and, for market launch, with mast mounting shown. All screws and nuts are made of stainless steel. The PL or N sockets used are high quality and PTFE dialectic. A tuner is required for non-resonant antennas. The following wire lengths have proven to be useful:6.5m - 6.9m - 13.5m - 13.9m - 16.2m - 20.8m - 22m - 26m - 27.7m - 34.7m - 41.6m - 48.5m - 55.5m You can find suitable antenna strands here: Copper Kevlar stranded wire Translated with DeepL.com (free version)

Mosquito End Fed 1:9 Antenna Mosquito End Fed – small and light After the Mini-End Fed was so well accepted, we looked at how we could make the whole thing even smaller, more compact but robust. The main focus here was on weight. The result is the Moskito End Fed. Mosquito? Yes, because it is so tiny and light. The cylindrical housing with a height of only 70mm and a diameter of 25mm weighs just 50 grams. This makes the Moskito easy to stow in your pocket or backpack. The maximum output is 50 watts SSB PEP. It is available in 1:49 and 1:9. This makes the Moskito End Fed antenna ideal for portable use when traveling, QRP, COTA, POTA, IOTA, SOTA (Summit on the Air) or DX expeditions etc. The Moskito End Fed is suitable for the new generation of small multiband/multimode QRP transceivers such as the Icom IC-705, Xiegu G90 or X6100, LAB 599 TX500 or the Yaesu FT-817/818. Super light antenna wire To match the lightweight Moskito End Fed, we offer the new, super lightweight and high-strength antenna wire SL as an option. This antenna wire is only 1.6mm thick, weighs 4g per meter and consists of 6×0.25mm tinned copper wires. The stranded wire has a core made of tear-resistant Vectran fibers® and a weatherproof PE insulation. This achieves a maximum breaking load of up to 60kg! If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you can be on air within a few minutes! To attach the housing of the 1:9 transformer to a mast, the mini insulator and a carabiner are all you need. Counter-poise If a counter-poise is required, you can connect a short piece of wire/strand with a length of 0.05 λ to the side connection of the mosquito antenna. The counter-poise should hang down freely.

Mosquito End Fed 1:49 – small and light After the Mini-End Fed was so well accepted, we looked at how we could make the whole thing even smaller, more compact but robust. The main focus here was on weight. The result is the Moskito End Fed. Mosquito? Yes, because it is so tiny and light. The cylindrical housing with a height of only 70mm and a diameter of 25mm weighs just 50 grams. This makes the Moskito easy to stow in your pocket or backpack. The maximum output is 50 watts SSB PEP. It is available in 1:49 and 1:9. This makes the Moskito End Fed antenna ideal for portable use when traveling, QRP, COTA, POTA, IOTA, SOTA (Summit on the Air) or DX expeditions etc. The Moskito End Fed is suitable for the new generation of small multiband/multimode QRP transceivers such as the Icom IC-705, Xiegu G90 or X6100, LAB 599 TX500 or the Yaesu FT-817/818. Super light antenna wire To match the lightweight Moskito End Fed, we offer the new, super lightweight and high-strength antenna wire SL as an option. This antenna wire is only 1.6mm thick, weighs 4g per meter and consists of 6×0.25mm tinned copper wires. The stranded wire has a core made of tear-resistant Vectran fibers® and a weatherproof PE insulation. This achieves a maximum breaking load of up to 60kg! If you attach the antenna to the top of a telescopic mast and slide out the mast segments, you can be on air within a few minutes! To attach the housing of the 1:9 transformer to a mast, the mini insulator and a carabiner are all you need. Counter-poise If a counter-poise is required, you can connect a short piece of wire/strand with a length of 0.05 λ to the side connection of the mosquito antenna. The counter-poise should hang down freely.

1:9 UNUN transformer for the frequency range: 1-30MHz and a maximum transmission power of either 600W or 1500W PEP. The IP67 housing is of course made of UV-resistant polycarbonate. Including connection for a counterweight and, for market launch, with mast mounting shown. All screws and nuts are made of stainless steel. The PL or N sockets used are high quality and PTFE dialectic. A tuner is required for non-resonant antennas. The following wire lengths have proven to be useful:6.5m - 6.9m - 13.5m - 13.9m - 16.2m - 20.8m - 22m - 26m - 27.7m - 34.7m - 41.6m - 48.5m - 55.5m You can find suitable antenna strands here: Copper Kevlar stranded wireInformationen gemäß Art. 19 GPSR Adresse des Herstellers: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net Adresse der verantwortlichen Person: Bonito - Gerichtsweg 3 - 29320 Hermmansburg - anfragen@bonito.net- www.bonito.net

Multi Isolator Maxi 120x16x16mm Der Multi Isolator Maxi aus Polycarbonat, ist stark, leicht, witterungs- und UV-beständig. Der Multi Isolator Maxi ist multifunktional einsetzbar, zum Beispiel als Zugentlastung für Dipole und EndFed Antennen. Abmessungen; 120x16x16mm Material: Wetter und UV-beständigiges Polycarbonat Isolator, Endfed, Fritzel, Dipol, Antennen, Hamradio, Amateurfunk , FR1901, fritzel isolator

Capacitor 100 pF 3 kV The proven capacitors used in our Endfed and Mini-Endfed kits. The capacitor is used for the EndFed impedance transformer to compensate the (unwanted) secondary capacitance.